Forums > General Discussion > What are the common operation problems of labeling machines? Do you have any good skills for operating the labeling machine?
| What are the common operation problems of labeling machines? Do you have any good skills for operating the labeling machine? | |
|---|---|
| Posted: 14 Jun 2022 03:03 UTC | Post #1 |
| beilt Deck & Engine |
Registered Total Posts: 7 |
| A labeling machine is a device that sticks rolls of self-adhesive paper labels (paper or metal foil) on PCBs, products or prescribed packaging. Labeling machines are an integral part of modern packaging. At present, the types of labeling machines produced in my country are gradually increasing, and the technical level has also been greatly improved. It has shifted from the backward situation of manual and semi-automatic labeling to the pattern of automatic high-speed labeling machines occupying the vast market. Labeling machine operation problems and solutions 1. The phenomenon of missing labeling of the labeling machine, the main reason for the phenomenon of missing labeling of the labeling machine is that the sensor does not sense in time. Labeling machine missing sticker solution: The first method is to reduce the speed of the labeling machine, and the leakage phenomenon will be greatly reduced, but it is difficult to achieve no leakage. The second method is to adjust the sensor data according to the image, the data on the left is the larger data, and the data on the right is smaller. In general, the leakage phenomenon of the labeling machine is that the induction sensitivity is not enough, and it should be adjusted to be small. Relatively speaking, the value of freeze-dried powder should be large, and the value of solution should be small. The lyophilized powder data ranges from several hundred to more than 2000, and the solution ranges from dozens to 500. Debug slowly. 2. There is bubbling in the labeling of the labeling machine, the causes and solutions of the bubbling phenomenon of the labeling machine: First, the pressure label position is not clamped, adjust the position adjustment wheel below the label pressure position of the labeling machine, and turn it to the right to clamp. Second, the speed is too slow. Increasing the speed of the labeling machine can also reduce the generation of bubbles. Third, adjust the labeling machine's labeling position in the technician parameters, and increase or decrease it according to the actual situation. labeli ng machine Labeling machine operation tips 1. For products with a relatively thin front end of the bottle, such as a point-sealed bottle, when the labeling machine is used, the label should be attached to the front-end inverted bottle detector for easy operation. 2. When changing the mold, the transmission shaft of the rotary labeling machine should be slightly to the right than the rotary wheel, so that it is not easy to burst the bottle. Another little secret is to test whether the installation is good or not. If you have no experience, it is best to choose powder, and not a solution. Because it is easy to clean up if the bottle bursts. In addition, it should be noted that the right end of the rotating transmission shaft of the labeling machine must be pressed against the bottom, and the two fixing screws on the left should be tightened after adjusting the position. 3. Each time the labeling machine changes the label, the position of each card wheel must be adjusted well, and the labels of the labeling machine should be placed on the same parallel plane as much as possible, so that the labels posted are much neater. 4. Label testing must be done every time the label is changed. This is actually a process for the labeling machine to record the parameters. 5. When the labeling machine is out of the label test, it is best that the length of the leaking end is 4-5 mm. It is not easy to roll when it is long, and it is not very good when it is short. 6. The serving rubber wheel should not be clamped too loosely or too tightly. It can twitch the label of the labeling machine, and it is not necessary to use too much force. The rubber wheel is not clamped on the computer side. In fact, just restore it and it will be fine. Don't try to clamp the rubber wheel. 7. When there is a lack of label prompt, or the labeling machine cannot detect the upper and lower positions of the label, it is good to adjust the upper and lower positions of the detector. Otherwise, the labeling machine is missing the label. At this time, press the reset button, and then click the jog out of the label on the parameter setting page, and walk past the missing label position. 8. When wrapping the label, there is a principle, that is, do not go back, from left to right, there will be no circumstance of going around the left and then to the right. The specific labeling machine wraps the label, and you will be familiar with it twice For more information, please follow the link below: https://www.beiltmac hinery.com/. | |
1 / 1